Wind Turbine Solar Street Lamp Outside

Wind Turbine Solar Street Lamp Outside

300W/400W Wind Turbine Solar Street Lamp Outside General Introduction: DC System Diagram Principle: Wind powered turbine and solar panel charge the battery by automatic controller, then the controller controls on and off of DC street lamp. System Configuration Wind solar hybrid street light...
Chat Now

Product Details

300W/400W Wind Turbine Solar Street Lamp Outside
General Introduction:
DC System Diagram

Principle: Wind powered turbine and solar panel charge the battery by automatic controller, then the controller controls on and off of DC street lamp.

11.jpg

System Configuration

22.jpg

Wind solar hybrid street light system is mainly combine by wind driven generator, solar panels, automatic controller, batteries, battery boxes, lamp and pole.


Installation Procedure:

33.jpg


Brief description:
1. Geological survey: Select appropriate mounting site.
2. Foundation: excavate the foundation according to design specification, the strength of concrete should not be less than C25, the cable goes through pipes in the foundation and out from foundation central exceeds 30-50mm above the ground.
3. Pole threading: draw out the wires from turbine, solar panel and lamp from light pole.
4. Assemble turbine: refer to turbine manual.
5. Installation of solar panels: fix the support of panel on the pole at designed height and pay attention to its angle should in accordance with requirement. Mount the panels on the support, and make confirmation, then shield the panel and wire it to the wiring box of battery and pay attention to plus or minus polar.
6. Fix the lamp: fix the lamp (light fixture and light source) with the pole.
7. Erect the pole: erect the pole by crane.


Auto controller wiring diagram:
Wiring order: wire the battery箭头.jpgoutput overload箭头.jpgsolar panel箭头.jpgturbine
Mistake in wiring order might cause fault of controller

image017_副本.jpg

Note: Install the controller inside the pole, the plug should towards down in case of water entering in.


Common fault and handling:

Fault

Fault reason

Exclusion methods

Fierce shaking of turbine

1. The bolt is loosen
2. The blade is transformed
3. The blade is out of nimbleness
1. Tighten up the loosen part
2. Change the blade
3. Dismount lubricating maintenance and re-install

Direction adjust not flexible

1. Too much grease and dust inside the base rotation;
2. Sand or dust inside the base rotation;
3. The turbine ever been fallen down, the upper end of pole is transformed
1. Lubricating maintenance
2. Clear the stuff and lubricating
3. Alignment top end of pole

Unusual noise

1. Loosen parts in each tightening parts
2. The bearing of generator is loosen
3. The bearing of generator is damaged
4. Friction between generator rotor and stator (usually the reason of bearing)
1. Put down the turbine and check and adopt relevant measures;
2. Change bearing and re-install
3. Change bearing
4. Change or repair the bearing

The rotating speed of wheel is obviously reduced

1. The generator is not be lubricated and maintained for long tome
2. The generator bearing is damaged
3. The blade is transformed
1. Maintain with lubrication oil
2. Change bearing
3. Repair or change blades

The output voltage of generator is too low or do not work

1. Short circuit
2. Turn off
3. Poor contacts of the wiring plugs
4. The generator rotor and stator are loosen
1. Check and deal with
2. Check and deal with
3. Check and deal with
4. Replace the motor

The output voltage of solar panel is too low or too high

1. Short circuit
2. Turn off
3. Poor contacts of the wiring plugs


1. Check and deal with
2. Check and deal with
3. Check and deal with


The battery is not chargeable

1. The output voltage of generator is too low or does not charge
2. The output voltage of panel is too low or no voltage
3. The connection poles of battery is rusted or poor
4. The battery runs out
5. Auto-controller or inverter is damaged
1. Clear by above methods;
2. Clear by above methods;
3. Clear rust, keep fine connection and coat with vaseline
4. Replace the battery
5. Replace controller or inverter

Power lack or power off

See "The output voltage of generator is too low or do not work" and "The battery is not chargeable"

See fault shooting methods

The lamp works irregularly

1. Controller or inverter sets incorrectly.
2. Controller or inverter is damaged
1. Check the setting according to manual.
2. Replace the controller or inverter


Series Products Installation Picture:


  image021_副本.jpg

  image025_副本.jpg


Inquiry